13518219792
一.测试拓扑：
成都创新互联公司专注于石嘴山网站建设服务及定制，我们拥有丰富的企业做网站经验。 热诚为您提供石嘴山营销型网站建设，石嘴山网站制作、石嘴山网页设计、石嘴山网站官网定制、成都微信小程序服务，打造石嘴山网络公司原创品牌,更为您提供石嘴山网站排名全网营销落地服务。
R1------------SW1------------------(MAC:2.2.2)R2
|
R3
R1，R2，R3都在VLAN11中，R1连接SW1的接口手工指定mac地址为1.1.1,R2连接SW1的接口手工指定mac地址为2.2.2;
R1接口的IP地址为10.1.1.1;
R2接口的IP地址为10.1.1.2;
R3接口的IP地址为10.1.1.3.
二.交换机VACL第一种配置方式：
mac access-list extended R2
permit host 0002.0002.0002 any （只能屏蔽非IP包，比如arp包）
access-list 100 permit ip host 10.1.1.3 any
vlan access-map test 10
match ip address 100
action drop
vlan access-map test 20
match mac address R2
action drop
vlan access-map test 30
action forward
!
vlan filter test vlan-list 11
因为SW1拒绝了R2发出的非IP包（arp回应包被拒绝了），R1和R3没有R2接口地址的ARP条目，导致R1无法ping和telnet R2，如果R1手工添加R2接口地址的ARP条目，R1则能pint和telnet R2，返回过来也可以。
A.R1 PING R3
R1#ping 10.1.1.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
R3#
*Feb 12 11:19:41.002: ICMP: echo reply sent, src 10.1.1.3, dst 10.1.1.1
*Feb 12 11:19:43.002: ICMP: echo reply sent, src 10.1.1.3, dst 10.1.1.1
*Feb 12 11:19:45.002: ICMP: echo reply sent, src 10.1.1.3, dst 10.1.1.1
*Feb 12 11:19:47.002: ICMP: echo reply sent, src 10.1.1.3, dst 10.1.1.1
*Feb 12 11:19:49.002: ICMP: echo reply sent, src 10.1.1.3, dst 10.1.1.1
B.R3 PING R1
R3#ping 10.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
在R1上开启debug没有看到数据包到达R1
C.R1 PING R2
R1#ping 10.1.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.2, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
R1#
在R2上开启debug没有看到数据包到达R2
D.R2 PING R1
R2#ping 10.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
R1#
*May 23 00:05:21.700: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.2
*May 23 00:05:23.696: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.2
*May 23 00:05:25.696: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.2
*May 23 00:05:27.696: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.2
*May 23 00:05:29.696: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.2
E.R2 ping R3
R2#ping 10.1.1.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
在R3上开启debug没有看到数据包到达R3
F.R3 ping R2
R3#ping 10.1.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.2, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
在R2上开启debug没有看到数据包到达R2
三.交换机VACL第二种配置方式：
mac access-list extended R2
permit any host 0002.0002.0002 （只能屏蔽非IP包，比如arp包）
access-list 100 permit ip any host 10.1.1.3
vlan access-map test 10
match ip address 100
action drop
vlan access-map test 20
match mac address R2
action drop
vlan access-map test 30
action forward
!
vlan filter test vlan-list 11
因为SW1拒绝去往R2的非IP包（R1和R2给R2的arp回应包被拒绝了），R2没有R1和R3接口地址的ARP条目，导致R1无法ping和telnet R2，如果R2手工添加R1接口地址的ARP条目，R1则能pint和telnet R2，返回过来也可以。A.R1 PING R3
R1#ping 10.1.1.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
在R3上开启debug没有看到数据包到达R3
B.R3 PING R1
R3#ping 10.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
R1#
*May 23 00:20:36.024: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.3
*May 23 00:20:38.020: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.3
*May 23 00:20:40.020: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.3
*May 23 00:20:42.020: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.3
*May 23 00:20:44.020: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.3
C.R1 PING R2
R1#ping 10.1.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.2, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/1/1 ms
R2#
*Jun 15 10:42:29.990: ICMP: echo reply sent, src 10.1.1.2, dst 10.1.1.1
*Jun 15 10:42:29.990: ICMP: echo reply sent, src 10.1.1.2, dst 10.1.1.1
*Jun 15 10:42:29.990: ICMP: echo reply sent, src 10.1.1.2, dst 10.1.1.1
*Jun 15 10:42:29.994: ICMP: echo reply sent, src 10.1.1.2, dst 10.1.1.1
D.R2 PING R1
R2#ping 10.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
R1#
*May 23 00:23:03.836: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.2
*May 23 00:23:03.836: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.2
*May 23 00:23:03.836: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.2
*May 23 00:23:03.836: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.2
*May 23 00:23:03.836: ICMP: echo reply sent, src 10.1.1.1, dst 10.1.1.2
E.R2 ping R3
R2#ping 10.1.1.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
在R3上开启debug没有看到数据包到达R3
F.R3 ping R2
R3#ping 10.1.1.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.2, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
R2#
*Jun 15 11:16:23.882: ICMP: echo reply sent, src 10.1.1.2, dst 10.1.1.3
*Jun 15 11:16:25.882: ICMP: echo reply sent, src 10.1.1.2, dst 10.1.1.3
*Jun 15 11:16:27.882: ICMP: echo reply sent, src 10.1.1.2, dst 10.1.1.3
*Jun 15 11:16:29.882: ICMP: echo reply sent, src 10.1.1.2, dst 10.1.1.3
四.总结：
A.mac地址过滤，只能过滤非IP流量，不能过滤IP流量
B.icmp属于IP层的协议，icmp流量属于ip流量
C.arp流量不属于IP流量，mac地址过滤导致arp无法正常工作，才会导致ip层协议出现问题，如果手工添加ARP条目，就能是IP流量正常通行。
